Drill Bits

These Faithfull SDS Plus Chisel Bits are made from drop-forged chrome molybdenum with a heat-treated tempered edge. Molybdenum is ideally suited for chisels because of its known reputation for hardness, toughness and wear resistance. Used mainly for light demolition, chiselling, stripping plaster, mortar chasing, channelling and breaking through brickwork.

These Faithfull SDS Plus Chisel Bits are made from drop-forged chrome molybdenum with a heat-treated tempered edge. Molybdenum is ideally suited for chisels because of its known reputation for hardness, toughness and wear resistance. Used mainly for light demolition, chiselling, stripping plaster, mortar chasing, channelling and breaking through brickwork.

A high performance drill bit with a superior European carbide tip to give extended durability. German tested and PGM approved to ensure the bits drill with dimensional precision and performance when used in concrete and masonry. Rebar drilling will result in reduced tool life. All chisel tip SDS drills can shear if the tip snags the reinforcing whilst passing alongside. This bit features a special nickel chromoly shank and a high quality European BC20 Tungsten Carbide tip. Cold formed blanks utilised up to 11mm diameter and fully heat treated to eliminate bending. Twin flute design for increased drilling performance and shot-peened for increased strength and durability.

The twin cutting edge and integral centre point enhances speed and provides rapid chip removal when drilling various types of timber and man-made boards. Three point design for faster, cleaner holes in a bright finish. Compound angle, ground recessed cutting edge for superior cutting and 1/4” Quick release hexagonal shank for use in both 3 jaw chucks and 1/4” quick release adaptors.

The DEWALT SDS Plus EXTREME 2®Drill Bit is made from superior carbide grade for long life and greater durability. The hardened body adds further strength and helps to reduce breakage. Its optimised flute design provides efficient debris removal whilst the tip design ensures better bit penetration.

This DEWALT SDS Plus EXTREME 2® Drill Bit has the following dimensions:

Diameter: 6mm
Working Length: 150mm
Overall Length: 210mm
Pack Quantity: 1

The DEWALT Extreme Flatwood Drill Bits have an extra thick robust steel shank for outstanding durability and chamfered outer cutting spurs for clean, very fast drilling and extended drilling life. The precision ground central point has an optimised design for faster material penetration and increased drilling speed.

Ideal for the rapid drilling of holes in wood, for door locks, mortising, electrical and plumbing work. Suitable for natural hard and soft wood, chipboard and other man made materials.

A high performance wood drill for drilling a deep hole into various types of timber in a bright and black finish. Made from high grade carbon Steel with a screw point.

The DEWALT SDS Plus EXTREME 2®Drill Bit is made from superior carbide grade for long life and greater durability. The hardened body adds further strength and helps to reduce breakage. Its optimised flute design provides efficient debris removal whilst the tip design ensures better bit penetration.

This DEWALT SDS Plus EXTREME 2® Drill Bit has the following dimensions:

Diameter: 10mm
Working Length: 150mm
Overall Length: 210mm
Pack Quantity: 1

A high quality, cost effective drill bit suitable for use in rotary hammers with the SDS plus tool system. Fully heat treated to eliminate bending and in a shot blast finish for rust protection.

Suitable for the wet drilling of porcelain, marble, granite and travertine tiles with a nickel plated body and an electro plated diamond cutting rim with a straight shank that fits all drill chucks. For best results use with Tile Rite universal guide and cooling system. Hole size suitable for brown solid wall plug.

A high performance drill bit with a superior European carbide tip to give extended durability. German tested and PGM approved to ensure the bits drill with dimensional precision and performance when used in concrete and masonry. Rebar drilling will result in reduced tool life. All chisel tip SDS drills can shear if the tip snags the reinforcing whilst passing alongside. This bit features a special nickel chromoly shank and a high quality European BC20 Tungsten Carbide tip. Cold formed blanks utilised up to 11mm diameter and fully heat treated to eliminate bending. Twin flute design for increased drilling performance and shot-peened for increased strength and durability.

The DEWALT Extreme Masonry Drill Bits offer excellent quality for all types of masonry work. They last up to 2 times longer and deliver up to 50% more holes per charge on a cordless drill than a standard masonry bit. Optimum carbide grade maximises durability.

A unique tip design provides an efficient drilling action and reduced walking for greater accuracy. Optimised milled flute offers fast drilling and the special copper brazing withstands high temperatures.

Applications: Typically used for drilling anchors, plastic plugs, fixings or pipework clearance holes.

Suitable for masonry, brick, stone, tiles and light concrete.

This DEWALT Extreme Masonry Drill Bit has the following specification:

Diameter: 12mm
Overall Length: 150mm
Working Length: 100mm

A high quality, cost effective drill bit suitable for use in rotary hammers with the SDS plus tool system. Fully heat treated to eliminate bending and in a shot blast finish for rust protection.

A high performance wood drill for drilling a deep hole into various types of timber in a bright and black finish. Made from high grade carbon Steel with a screw point.

These DEWALT multi-material drill bits can be used in wood, masonry and metal and are ideal when drilling near to corners and edges.

The drill bits have a fully supported carbide head which gives faster drilling and a non slip shank which ensures maximum retention in chuck. They can be used in rotary or percussion drilling modes.

The DEWALT DEWDT6525QZ multi material drill bit has the following dimensions:
Size: 12mm x 153mm.

The twin cutting edge and integral centre point enhances speed and provides rapid chip removal when drilling various types of timber and man-made boards. Three point design for faster, cleaner holes in a bright finish. Compound angle, ground recessed cutting edge for superior cutting and 1/4” Quick release hexagonal shank for use in both 3 jaw chucks and 1/4” quick release adaptors.

The twin cutting edge and integral centre point enhances speed and provides rapid chip removal when drilling various types of timber and man-made boards. Three point design for faster, cleaner holes in a bright finish. Compound angle, ground recessed cutting edge for superior cutting and 1/4” Quick release hexagonal shank for use in both 3 jaw chucks and 1/4” quick release adaptors.

The nylon brush is less aggressive and ideal for light de-burring, polishing and finishing.

The DEWALT SDS Plus EXTREME 2®Drill Bit is made from superior carbide grade for long life and greater durability. The hardened body adds further strength and helps to reduce breakage. Its optimised flute design provides efficient debris removal whilst the tip design ensures better bit penetration.

This DEWALT SDS Plus EXTREME 2® Drill Bit has the following dimensions:

Diameter: 7mm
Working Length: 150mm
Overall Length: 210mm
Pack Quantity: 1

A high performance drill bit with a superior European carbide tip to give extended durability. Rebar drilling will result in Reduced tool life. All chisel tip SDS drills can shear if the tip snags the reinforcing whilst passing alongside. This bit features a special nickel chromoly shank, a high quality European BC20 Tungsten Carbide tip. Cold formed blanks utilised up to 11mm diameter and fully heat treated to eliminate bending. Twin flute design for increased drilling performance and shot-peened for increased strength and durability.

These Faithfull SDS Plus Chisel Bits are made from drop-forged chrome molybdenum with a heat-treated tempered edge. Molybdenum is ideally suited for chisels because of its known reputation for hardness, toughness and wear resistance. Used mainly for light demolition, chiselling, stripping plaster, mortar chasing, channelling and breaking through brickwork.

The Faithfull Carbon Steel Rosehead 60° included angle countersink. For countersinking screw holes in wood for the flush fitting of screw heads.

A premium quality masonry heat treated bit for use in cordless and corded drill drivers in both rotary and hammer action. 130° high grade industrial carbide tip in a silver and black finish.

The DEWALT SDS Plus EXTREME 2®Drill Bit is made from superior carbide grade for long life and greater durability. The hardened body adds further strength and helps to reduce breakage. Its optimised flute design provides efficient debris removal whilst the tip design ensures better bit penetration.

This DEWALT SDS Plus EXTREME 2® Drill Bit has the following dimensions:

Diameter: 12mm
Working Length: 150mm
Overall Length: 200mm
Pack Quantity: 1

A high performance drill bit with a superior European carbide tip to give extended durability. Rebar drilling will result in Reduced tool life. All chisel tip SDS drills can shear if the tip snags the reinforcing whilst passing alongside. This bit features a special nickel chromoly shank, a high quality European BC20 Tungsten Carbide tip. Cold formed blanks utilised up to 11mm diameter and fully heat treated to eliminate bending. Twin flute design for increased drilling performance and shot-peened for increased strength and durability.

The DEWALT Extreme Flatwood Drill Bits have an extra thick robust steel shank for outstanding durability and chamfered outer cutting spurs for clean, very fast drilling and extended drilling life. The precision ground central point has an optimised design for faster material penetration and increased drilling speed.

Ideal for the rapid drilling of holes in wood, for door locks, mortising, electrical and plumbing work. Suitable for natural hard and soft wood, chipboard and other man made materials.

Manufactured from a high grade M2 tool Steel. This durable engineering quality drill will give a consistent rapid performance into all non-alloy materials. The 135° split point prevents the bit from drifting and enables faster penetration. Fully ground from solid material and dimensionally precise. Manufactured to DIN 338.

A high performance drill bit with a superior European carbide tip to give extended durability. German tested and PGM approved to ensure the bits drill with dimensional precision and performance when used in concrete and masonry. Rebar drilling will result in Reduced tool life. All chisel tip SDS drills can shear if the tip snags the reinforcing whilst passing alongside. This bit features a special nickel chromoly shank and a high quality European BC20 Tungsten Carbide tip. Cold formed blanks utilised up to 11mm diameter and fully heat treated to eliminate bending. Twin flute design for increased drilling performance and shot-peened for increased strength and durability.

A high performance wood drill for drilling a deep hole into various types of timber in a bright and black finish. Made from high grade carbon Steel with a screw point.

A high quality, cost effective drill bit suitable for use in rotary hammers with the SDS plus tool system. Fully heat treated to eliminate bending and in a shot blast finish for rust protection.

Suitable for the wet drilling of porcelain, marble, granite and travertine tiles with a nickel plated body and an electro plated diamond cutting rim with a straight shank that fits all drill chucks. For best results use with Tile Rite universal guide and cooling system. Hole size suitable for red wall plug.

An economic High Speed Steel drill used for drilling all non-alloy materials. The 135° split point prevents the bit from drifting and enables faster penetration. Dimensionally precise and roll forged in a black oxide finish. Manufactured to DIN 338.

The Faithfull Carbon Steel Rosehead 60° included angle countersink. For countersinking screw holes in wood for the flush fitting of screw heads.

The Faithfull Metric HSS Drill Bit Sets are designed for cutting metal, however they are also suitable for drilling holes in timber, chipboard and plywood. The sets have an easy flip open action case with transparent front for easy checking of contents.

A high performance drill bit with a superior European carbide tip to give extended durability. German tested and PGM approved to ensure the bits drill with dimensional precision and performance when used in concrete and masonry. Rebar drilling will result in reduced tool life. All chisel tip SDS drills can shear if the tip snags the reinforcing whilst passing alongside. This bit features a special nickel chromoly shank and a high quality European BC20 Tungsten Carbide tip. Cold formed blanks utilised up to 11mm diameter and fully heat treated to eliminate bending. Twin flute design for increased drilling performance and shot-peened for increased strength and durability.

A high quality, cost effective drill bit suitable for use in rotary hammers with the SDS plus tool system. Fully heat treated to eliminate bending and in a shot blast finish for rust protection.

A premium quality masonry heat treated bit for use in cordless and corded drill drivers in both rotary and hammer action. 130° high grade industrial carbide tip in a silver and black finish.

The DEWALT Extreme Flatwood Drill Bits have an extra thick robust steel shank for outstanding durability and chamfered outer cutting spurs for clean, very fast drilling and extended drilling life. The precision ground central point has an optimised design for faster material penetration and increased drilling speed.

Ideal for the rapid drilling of holes in wood, for door locks, mortising, electrical and plumbing work. Suitable for natural hard and soft wood, chipboard and other man made materials.

The BlueSpot 3 Piece SDS plus Chisel Set is specially designed for chipping and chiselling of glazing compounds, mortar, tile and other masonry products. Perfect for all chasing and demolition work in mortar, brick and concrete. Heat-treated for increased durability and suitable for use with SDS plus power drills with a roto-stop function. Includes 3 SDS plus chisels.

The nylon brush is less aggressive and ideal for light de-burring, polishing and finishing.

A high performance drill bit with a superior European carbide tip to give extended durability. German tested and PGM approved to ensure the bits drill with dimensional precision and performance when used in concrete and masonry. Rebar drilling will result in reduced tool life. All chisel tip SDS drills can shear if the tip snags the reinforcing whilst passing alongside. This bit features a special nickel chromoly shank and a high quality European BC20 Tungsten Carbide tip. Cold formed blanks utilised up to 11mm diameter and fully heat treated to eliminate bending. Twin flute design for increased drilling performance and shot-peened for increased strength and durability.

The DEWALT SDS Plus EXTREME 2®Drill Bit is made from superior carbide grade for long life and greater durability. The hardened body adds further strength and helps to reduce breakage. Its optimised flute design provides efficient debris removal whilst the tip design ensures better bit penetration.

This DEWALT SDS Plus EXTREME 2® Drill Bit has the following dimensions:

Diameter: 16mm
Working Length: 100mm
Overall Length: 160mm
Pack Quantity: 1

A premium quality masonry heat treated bit for use in cordless and corded drill drivers in both rotary and hammer action. 130° high grade industrial carbide tip in a silver and black finish.

The DEWALT SDS Plus EXTREME 2®Drill Bit is made from superior carbide grade for long life and greater durability. The hardened body adds further strength and helps to reduce breakage. Its optimised flute design provides efficient debris removal whilst the tip design ensures better bit penetration.

This DEWALT SDS Plus EXTREME 2® Drill Bit has the following dimensions:

Diameter: 14mm
Working Length: 150mm
Overall Length: 200mm
Pack Quantity: 1

Manufactured from a high grade M2 tool Steel. This durable engineering quality drill will give a consistent rapid performance into all non-alloy materials. The 135° split point prevents the bit from drifting and enables faster penetration. Fully ground from solid material and dimensionally precise. Manufactured to DIN 338.

Trend Snappy Snap/CS/6 Drill Countersink 2.5mm. 9.5mm diameter countersink - with adjustable 2.5mm pilot drill. 9.5mm diameter countersink with pilot drill designed for Imperial No6 gauge screws in softwood. The perfect, fast swap accessory for clean, consistent finishes.
Made from hardened tool steel for assured performance. Ideally suited to hard and softwoods alike. Fitted with high quality 2.5mm diameter replaceable HSS (High Speed Steel) drill Ideal for metric screws up to 5mm gauge. Easily adjustable drill length for different timber thicknesses and fast alignment. Can be used to make countersinks and can also be used for counterbores; ideal for use with Trend Snappy SNAP/PC/95T or SNAP/PC/38 Plug Cutters for applications where the fixings need to be hidden.

Trend Snappy Snap/CS/4 Drill Countersink 2mm. Trend Snappy 9.5mm diameter countersink with adjustable 2mm drill. 9.5mm diameter countersink with pilot drill designed for Imperial gauge screws. The perfect, fast swap accessory for clean, consistent finishes. Made from hardened tool steel for assured performance. Fitted with high quality 2mm diameter replaceable HSS (High Speed Steel) designed for piloting in hardwoods using No4 Imperial gauge screws. Easily adjustable drill length for different timber thicknesses and fast alignment. Can be used to make countersinks and also counterbores when used with Trend Snappy SNAP/PC/95T or SNAP/PC/38 Plug Cutters for applications where the fixings need to be hidden.

Trend Snappy Snap/CS/8 Countersink 2.75mm. 9.5mm diameter countersink - with adjustable 2.75mm pilot drill. 9.5mm diameter countersink with pilot drill designed for Imperial screws up to 8 gauge. The perfect, fast swap accessory for clean, consistent finishes. Made from hardened tool steel for assured performance. Ideally suited to hard and softwoods alike. Fitted with high quality 2.75mm diameter replaceable HSS (High Speed Steel) drill designed for piloting work with Imperial screws up to 8 gauge in softwood and 6 gauge in hardwood. Easily adjustable drill length for different timber thicknesses and fast alignment. Can be used to make countersinks and can also be used for counterbores; ideal for use with Trend Snappy SNAP/PC/95T or SNAP/PC/38 Plug Cutters for applications where the fixings need to be hidden.

The BlueSpot 75mm x 165mm Flat SDS Plus Chisel is manufactured from carbon steel for high durability on demanding building sites and DIY applications. The product is ideal for the removal of wall and floor tiles, breaking up masonry and mortar as well as roughcasting, dirt and plaster from walls. The strengthened shaft and sharpened tip increase accuracy and longevity of the tool. The chisel is for use with an SDS drill.

The Vitrex Tile and Glass Drill Bits have a tungsten carbide tip, which gives them excellent strength and durability. The precision 'spearhead' design prevents chipping or breaking. They are ideal for drilling tiles and glass.

Trend Snappy Snap/CS/10 Countersink 3.25mm. 9.5mm diameter countersink - with adjustable 3.25mm pilot drill. 9.5mm diameter countersink with pilot drill designed for Imperial screws up to 8 gauge. The perfect, fast swap accessory for clean, consistent finishes. Made from hardened tool steel for assured performance. Ideally suited to hard and softwoods alike. Fitted with high quality 3.25mm diameter replaceable HSS (High Speed Steel) drill designed for piloting work with Imperial screws up to 8 gauge in softwood and 6 gauge in hardwood. Easily adjustable drill length for different timber thicknesses and fast alignment. Can be used to make countersinks and can also be used for counterbores; ideal for use with Trend Snappy SNAP/PC/95T or SNAP/PC/38 Plug Cutters for applications where the fixings need to be hidden.

Trend Snappy Snap/CS/12 Countersink 3.5mm. 12.7m diameter countersink - with adjustable 3.5mm pilot drill. 12.7mm diameter countersink with pilot drill designed for Imperial screws up to 8 gauge. The perfect, fast swap accessory for clean, consistent finishes. Made from hardened tool steel for assured performance. Ideally suited to hard and softwoods alike. Fitted with high quality 3.25mm diameter replaceable HSS (High Speed Steel) drill designed for piloting work with Imperial screws up to 8 gauge in softwood and 6 gauge in hardwood. Easily adjustable drill length for different timber thicknesses and fast alignment. Can be used to make countersinks and can also be used for counterbores; ideal for use with Trend Snappy SNAP/PC/95T or SNAP/PC/38 Plug Cutters for applications where the fixings need to be hidden.

The BlueSpot 11 Piece 19mm - 64mm Hole Saw Set is ideal for non-ferrous metals, plasterboard, plastic and wood. Manufactured from heat-treated carbon steel for increased durability and cutting power and includes a handy carrying case for quick and convenient storage. Includes hex key and arbors.

A high quality, cost effective drill bit suitable for use in rotary hammers with the SDS plus tool system. Fully heat treated to eliminate bending and in a shot blast finish for rust protection.

An economic High Speed Steel drill used for drilling all non-alloy materials. The 135° split point prevents the bit from drifting and enables faster penetration. Dimensionally precise and roll forged in a black oxide finish. Manufactured to DIN 338.

A premium quality masonry heat treated bit for use in cordless and corded drill drivers in both rotary and hammer action. 130° high grade industrial carbide tip in a silver and black finish.

The DEWALT Extreme Flatwood Drill Bits have an extra thick robust steel shank for outstanding durability and chamfered outer cutting spurs for clean, very fast drilling and extended drilling life. The precision ground central point has an optimised design for faster material penetration and increased drilling speed.

Ideal for the rapid drilling of holes in wood, for door locks, mortising, electrical and plumbing work. Suitable for natural hard and soft wood, chipboard and other man made materials.

A high quality, cost effective drill bit suitable for use in rotary hammers with the SDS plus tool system. Fully heat treated to eliminate bending and in a shot blast finish for rust protection.

The DEWALT Extreme Flatwood Drill Bits have an extra thick robust steel shank for outstanding durability and chamfered outer cutting spurs for clean, very fast drilling and extended drilling life. The precision ground central point has an optimised design for faster material penetration and increased drilling speed.

Ideal for the rapid drilling of holes in wood, for door locks, mortising, electrical and plumbing work. Suitable for natural hard and soft wood, chipboard and other man made materials.

The DEWALT Extreme Masonry Drill Bits offer excellent quality for all types of masonry work. They last up to 2 times longer and deliver up to 50% more holes per charge on a cordless drill than a standard masonry bit. Optimum carbide grade maximises durability.

A unique tip design provides an efficient drilling action and reduced walking for greater accuracy. Optimised milled flute offers fast drilling and the special copper brazing withstands high temperatures.

Applications: Typically used for drilling anchors, plastic plugs, fixings or pipework clearance holes.

Suitable for masonry, brick, stone, tiles and light concrete.

This DEWALT Extreme Masonry Drill Bit has the following specification:
Diameter: 14mm
Overall Length: 150mm
Working Length: 100mm

Spectrum dry core accessories are manufactured from the highest grade steel to ensure thatthey can withstand the toughest use.
Zinc plating enhances the visual appearance and protects against against rust without leavingoil deposits.The most complete range of accessories to cover all machinery options and personal preferences.

The Faithfull 7 Piece Multi Holesaw Set is designed specifically for cutting a range of different diameter holes. Can cut holes up to 42mm in depth. The multi-holesaw set can be used on a wide variety of materials, including wood, chipboard, plywood, non-laminated plastics, plasterboard and non-ferrous metals except stainless steel. Suitable for use with most power drills, the set is supplied complete with a pilot drill.

A high performance wood drill for drilling a deep hole into various types of timber in a bright and black finish. Made from high grade carbon Steel with a screw point.

Faithfull standard masonry bits are for use in chucks up to 13mm capacity and suitable for general purpose drilling including bricks, blocks and cement render when used in an impact or percussion drill. Roll formed and treated body with a heavy-duty Tungsten Carbide tip and fast spiral for quick waste removal.

The Faithfull Brad Point Wood Drill Bits are the preferred cutting tip design for drilling wood, chipboard and MDF. This alloy steel drill has a steeper twist and a deeper flute than HSS bits for rapid clearance of waste. Ideal for use in dowelling jigs.
Set of 5 spur and point wood bits.
Sizes: 4, 5, 6, 8 and 10mm.

A high performance drill bit with a superior European carbide tip to give extended durability. German tested and PGM approved to ensure the bits drill with dimensional precision and performance when used in concrete and masonry. Rebar drilling will result in reduced tool life. All chisel tip SDS drills can shear if the tip snags the reinforcing whilst passing alongside. This bit features a special nickel chromoly shank and a high quality European BC20 Tungsten Carbide tip. Cold formed blanks utilised up to 11mm diameter and fully heat treated to eliminate bending. Twin flute design for increased drilling performance and shot-peened for increased strength and durability.

6mm Vitrex Diamond Grit Edged Drill Bit for drilling hard tiles. The slotted bit design makes for easy waste removal. It is suitable for drilling porcelain, granite, quarry, stone, marble, terracotta and ceramic tiles. Weight: 18g.

A high performance wood drill for drilling a deep hole into various types of timber in a bright and black finish. Made from high grade carbon Steel with a screw point.

An economic High Speed Steel drill used for drilling all non-alloy materials. The 135° split point prevents the bit from drifting and enables faster penetration. Dimensionally precise and roll forged in a black oxide finish. Manufactured to DIN 338.

The DEWALT SDS Plus EXTREME 2®Drill Bit is made from superior carbide grade for long life and greater durability. The hardened body adds further strength and helps to reduce breakage. Its optimised flute design provides efficient debris removal whilst the tip design ensures better bit penetration.

This DEWALT SDS Plus EXTREME 2® Drill Bit has the following dimensions:

Diameter: 16mm
Working Length: 150mm
Overall Length: 200mm
Pack Quantity: 1

Starrett Fast Cut Bi-Metal Holesaws provide a smoother, faster cut on a wide range of materials, when compared to the previous constant pitch saw. Improved tooth material and 5.5 TPI/25mm tooth form for enhanced heat and wear resistance and greater product life. Specifically suited to cutting stainless and mild steel sheet, they will also cut through tubes with a wall thickness of up to 3mm (1/8in).

Starrett Fast Cut Bi-Metal Holesaws provide a smoother, faster cut on a wide range of materials, when compared to the previous constant pitch saw. Improved tooth material and 5.5 TPI/25mm tooth form for enhanced heat and wear resistance and greater product life. Specifically suited to cutting stainless and mild steel sheet, they will also cut through tubes with a wall thickness of up to 3mm (1/8in).

Starrett Fast Cut Bi-Metal Holesaws provide a smoother, faster cut on a wide range of materials, when compared to the previous constant pitch saw. Improved tooth material and 5.5 TPI/25mm tooth form for enhanced heat and wear resistance and greater product life. Specifically suited to cutting stainless and mild steel sheet, they will also cut through tubes with a wall thickness of up to 3mm (1/8in).

Plug Cutters are used for cutting wood plugs to cover recessed screw holes to achieve a neat finish. For a perfect grain match use an offcut from the timber being plugged.

A high performance drill bit with a superior European carbide tip to give extended durability. German tested and PGM approved to ensure the bits drill with dimensional precision and performance when used in concrete and masonry. Rebar drilling will result in reduced tool life. All chisel tip SDS drills can shear if the tip snags the reinforcing whilst passing alongside. This bit features a special nickel chromoly shank and a high quality European BC20 Tungsten Carbide tip. Cold formed blanks utilised up to 11mm diameter and fully heat treated to eliminate bending. Twin flute design for increased drilling performance and shot-peened for increased strength and durability.

A high performance drill bit with a superior European carbide tip to give extended durability. German tested and PGM approved to ensure the bits drill with dimensional precision and performance when used in concrete and masonry. Rebar drilling will result in reduced tool life. All chisel tip SDS drills can shear if the tip snags the reinforcing whilst passing alongside. This bit features a special nickel chromoly shank and a high quality European BC20 Tungsten Carbide tip. Cold formed blanks utilised up to 11mm diameter and fully heat treated to eliminate bending. Twin flute design for increased drilling performance and shot-peened for increased strength and durability.

Faithfull heavy-Duty keyed chuck for use on both Rotary and Impact drills. Fitted with an anti-thrust bearing to increase the amount of grip and to prevent slipping when under load.

Manufactured from a high grade M2 tool Steel. This durable engineering quality drill will give a consistent rapid performance into all non-alloy materials. The 135° split point prevents the bit from drifting and enables faster penetration. Fully ground from solid material and dimensionally precise. Manufactured to DIN 338.

1/4” Extension Rods to be used where there is restricted access and in conjunction with a 1/4” shank Flat Wood Bit. Supplied with Allen Key.

The BlueSpot 8 Piece 6mm - 127mm Hole Saw Set is ideal for non-ferrous metals, plasterboard, plastic and wood. Manufactured from heat-treated carbon steel for increased durability and cutting power and includes a handy carrying case for quick and convenient storage. Includes arbors, hex key and reinforcing plate.

The DEWALT SDS Plus EXTREME 2®Drill Bit is made from superior carbide grade for long life and greater durability. The hardened body adds further strength and helps to reduce breakage. Its optimised flute design provides efficient debris removal whilst the tip design ensures better bit penetration.

This DEWALT SDS Plus EXTREME 2® Drill Bit has the following dimensions:

Diameter: 16mm
Working Length: 200mm
Overall Length: 260mm
Pack Quantity: 1

Plug Cutters are used for cutting wood plugs to cover recessed screw holes to achieve a neat finish. For a perfect grain match use an offcut from the timber being plugged.

8mm Vitrex Diamond Grit Edged Drill Bit for drilling hard tiles. The slotted bit design makes for easy waste removal. It is suitable for drilling porcelain, granite, quarry, stone, marble, terracotta and ceramic tiles. Weight: 21g.

The Vitrex Tile and Glass Drill Bits have a tungsten carbide tip, which gives them excellent strength and durability. The precision 'spearhead' design prevents chipping or breaking. They are ideal for drilling tiles and glass.

Plug Cutters are used for cutting wood plugs to cover recessed screw holes to achieve a neat finish. For a perfect grain match use an offcut from the timber being plugged.

Manufactured from a high grade M2 tool Steel. This durable engineering quality drill will give a consistent rapid performance into all non-alloy materials. The 135° split point prevents the bit from drifting and enables faster penetration. Fully ground from solid material and dimensionally precise. Manufactured to DIN 338.

Manufactured from a high grade M2 tool Steel. This durable engineering quality drill will give a consistent rapid performance into all non-alloy materials. The 135° split point prevents the bit from drifting and enables faster penetration. Fully ground from solid material and dimensionally precise. Manufactured to DIN 338.

Starrett Fast Cut Bi-Metal Holesaws provide a smoother, faster cut on a wide range of materials, when compared to the previous constant pitch saw. Improved tooth material and 5.5 TPI/25mm tooth form for enhanced heat and wear resistance and greater product life. Specifically suited to cutting stainless and mild steel sheet, they will also cut through tubes with a wall thickness of up to 3mm (1/8in). Available in different sizes.

The DEWALT SDS Plus EXTREME 2®Drill Bit is made from superior carbide grade for long life and greater durability. The hardened body adds further strength and helps to reduce breakage. Its optimised flute design provides efficient debris removal whilst the tip design ensures better bit penetration.

This DEWALT SDS Plus EXTREME 2® Drill Bit has the following dimensions:

Diameter: 18mm
Working Length: 150mm
Overall Length: 200mm
Pack Quantity: 1

A high performance wood drill for drilling a deep hole into various types of timber in a bright and black finish. Made from high grade carbon Steel with a screw point.

The Faithfull High Speed Steel Rosehead Chubby 90° included angle Countersink. For countersinking screw holes for flush fitting of screw heads in mild steel, plastics and non-ferrous metals. Also suitable for working in wood, plywood, MDF and other man made boards. Can be used in both hand tools and power drills.

10mm Vitrex Diamond Grit Edged Drill Bit for drilling hard tiles. The slotted bit design makes for easy waste removal. It is suitable for drilling porcelain, granite, quarry, stone, marble, terracotta and ceramic tiles. Weight: 25g.

Tayler Tools 19pc HSS Jobber drill set supplied in a metal storage case contains: 1.0mm - 10.0mm x 0.5mm

Starrett Fast Cut Bi-Metal Holesaws provide a smoother, faster cut on a wide range of materials, when compared to the previous constant pitch saw. Improved tooth material and 5.5 TPI/25mm tooth form for enhanced heat and wear resistance and greater product life. Specifically suited to cutting stainless and mild steel sheet, they will also cut through tubes with a wall thickness of up to 3mm (1/8in).

The Faithfull Metric HSS Drill Bit Sets are designed for cutting metal, however they are also suitable for drilling holes in timber, chipboard and plywood. The sets have an easy flip open action case with transparent front for easy checking of contents.

Suitable for the wet drilling of porcelain, marble, granite and travertine tiles with a nickel plated body and an electro plated diamond cutting rim with a straight shank that fits all drill chucks. For best results use with Tile Rite universal guide and cooling system. Hole size suitable for 15mm copper pipe.

The DEWALT SDS Plus EXTREME 2®Drill Bit is made from superior carbide grade for long life and greater durability. The hardened body adds further strength and helps to reduce breakage. Its optimised flute design provides efficient debris removal whilst the tip design ensures better bit penetration.

This DEWALT SDS Plus Extreme 2 Drill Bit has the following dimensions:

Diameter: 20mm
Working Length: 150mm
Overall Length: 200mm
Pack Quantity: 1

12mm Vitrex Diamond Grit Edged Drill Bit for drilling hard tiles. The slotted bit design makes for easy waste removal. It is suitable for drilling porcelain, granite, quarry, stone, marble, terracotta and ceramic tiles. Weight: 34g.

The Vitrex Tile and Glass Drill Bits have a tungsten carbide tip, which gives them excellent strength and durability. The precision 'spearhead' design prevents chipping or breaking. They are ideal for drilling tiles and glass.

Trend Snappy 9.5mm diameter TCT countersink - with adjustable pilot drill.
9.5mm diameter countersink with pilot drill designed for Imperial screws up to 8 gauge. The perfect, fast swap accessory for clean, consistent finishes. TCT cutting tips for assured, long life performance in all timbers and abrasive timber based materials including ply, MDF and chipboard. Fitted with high quality 2.75mm diameter replaceable HSS (High Speed Steel) drill designed for piloting work with Imperial screws up to No8 gauge in softwood and No6 gauge in hardwood. Easily adjustable drill length for different timber thicknesses and fast alignment. Can be used to make countersinks and can also be used for counterbores; ideal for use with Trend Snappy SNAP/PC/95T or SNAP/PC/38 Plug Cutters for applications where the fixings need to be hidden.